Model 830
| Name | Summary | Price | Buy |
|---|---|---|---|
| 3/8″ Brazed Heating Element – 15″ | 3/8″ Brazed Heating Element – 15″ | $84.00 | |
| 3/8″ Brazed Heating Element – 20″ | 3/8″ Brazed Heating Element – 20″ | $89.00 | |
| 3/8″ Brazed Heating Element – 25″ | 3/8″ Brazed Heating Element – 25″ | $91.00 | |
| 3/8″ Brazed Heating Element – 30″ | 3/8″ Brazed Heating Element – 30″ | $96.00 | |
| Brass Nut (undersized) for Stud Assembly | Brass nut is used to secure the element to the brass stud assembly post | $1.00 | |
| Element Pad Assembly (Lower Only) for 11″ Dual Heat (Not High Temp) | The lower element pad assembly is the pad located under the element on the lower carrier plate. The lower element pad assembly has a piece of foam rubber on the bottom side. | $79.00 | |
| Element Pad Assembly (Lower Only) for 16″ Dual Heat (Not High Temp) | The lower element pad assembly is the pad located under the element on the lower carrier plate. The lower element pad assembly has a piece of foam rubber on the bottom side. | $81.00 | |
| Element Pad Assembly (Upper Only) for 11″ Dual Heat (Not High Temp) | The Upper Element Pad Assembly is the pad located under the element on the seal bar on the upper carrier plate | $79.00 | |
| Element Pad Assembly (Upper Only) for 16″ Dual Heat (Not High Temp) | The Upper Element Pad Assembly is the pad located under the element on the seal bar on the upper carrier plate | $81.00 | |
| Element Pad Assembly – 15″ (14-5/8″) | New EPA for models 5300,6300,730,830 replaces part # 608-0002 6/3/13 | $30.00 | |
| Element Pad Assembly – 20″ (19-3/4″) | New EPA for models 5300,6300,730,830 replaces part # 608-0002 6/3/13 | $32.00 | |
| Element Pad Assembly – 25″ (24-7/8″) | New EPA for models 5300,6300,730,830 replaces part # 608-0002 6/3/13 | $35.00 | |
| Element Pad Assembly – 30″ (30.00″) | New EPA for models 5300,6300,730,830 replaces part # 608-0002 6/3/13 | $37.00 | |
| Element Pad Assembly – 35″ (35.00″) | New EPA for models 5300,6300,730,830 replaces part # 608-0002 6/3/13 | $40.00 | |
| Foot Switch (Electric, 3 Wire) with 8′ Cord (Not for models 235, 35 nor 35G) | Replacement Foot switch with 8′ wire for all models Except 235, 35 and 35G. See part #306-0069 for switch only (without cable) for ease of installation or if you have an extended cable (longer than 8′). | $108.85 | |
| Foot Switch without cord | Replacement Foot switch without cable. May be easier to install as no entry to case will be needed. Pay close attention to how wires are connected to your current switch so new switch can be wired correctly. | $56.85 | |
| Heating Element – 3/8″ x 11″ for 11″ Dual Heat Machines | Heating Element – 3/8″ x 11″ for 11″ Dual Heat Machines | $96.00 | |
| Heating Element – 3/8″ x 16″ for 16″ Dual Heat Machines | Heating Element – 3/8″ x 16″ for 16″ Dual Heat Machines | $101.00 | |
| High Tension Slider Assembly – Spring loaded element tensioner | *For Most Models* The High Tension Slider Assembly fits most machines. It does not fit the model 635HP, 235 series, model 50 and model 60. The Slider Assembly is the sliding post that the heater element attaches to that enables the heater element to expand when it heats. | $74.85 | |
| Locking Insulated Brass Stud Assembly | The locking insulated Brass stud assembly is the fixed post for the heater element. If you have any questions, refer to your Operator Manual or call Accu-Seal. | $30.00 | |
| Pressure Pad Assembly-20" | The pressure pad assembly is a piece of aluminum covered with red rubber and PTFE Fabric Tape. It is the pad opposite the heater element. | $24.00 | |
| Pressure Pad Assembly-25" | The pressure pad assembly is a piece of aluminum covered with red rubber and PTFE Fabric Tape. It is the pad opposite the heater element. | $28.00 | |
| Pressure Pad Assembly-30" | The pressure pad assembly is a piece of aluminum covered with red rubber and PTFE Fabric Tape. It is the pad opposite the heater element. | $31.00 | |
| Pressure Pad Assembly-35" | The pressure pad assembly is a piece of aluminum covered with red rubber and PTFE Fabric Tape. It is the pad opposite the heater element. | $35.00 | |
| Seal Jaw Service Kit for 630/730/830 (15″) | The Seal Jaw Service Kit includes: The element pad assembly, pressure pad assembly, 3/8″ heater element, one Stainless Steel finger nut, one brass nut, and a strip of 2 1/2″ PTFE Fabric tape with a 1″ non-adhesive zone for over the element. Not for Dual (Upper & Lower) heat versions. | $135.00 | |
| Seal Jaw Service Kit for 630/730/830 – 20″ | The Seal Jaw Service Kit includes: The element pad assembly, pressure pad assembly, 3/8″ heater element, one Stainless Steel finger nut, one brass nut, and a strip of 2 1/2″ PTFE Fabric tape with a 1″ non-adhesive zone for over the element. Not for Dual (Upper & Lower) heat versions. | $148.00 | |
| Seal Jaw Service Kit for 630/730/830 – 25″ | The Seal Jaw Service Kit includes: The element pad assembly, pressure pad assembly, 3/8″ heater element, one Stainless Steel finger nut, one brass nut, and a strip of 2 1/2″ PTFE Fabric tape with a 1″ non-adhesive zone for over the element. Not for Dual (Upper & Lower) heat versions. | $166.00 | |
| Seal Jaw Service Kit for 630/730/830 – 30″ | The Seal Jaw Service Kit includes: The element pad assembly, pressure pad assembly, 3/8″ heater element, one Stainless Steel finger nut, one brass nut, and a strip of 2 1/2″ PTFE Fabric tape with a 1″ non-adhesive zone for over the element. Not for Dual (Upper & Lower) heat versions. | $172.00 | |
| Seal Jaw Service Kit for 630/730/830 – 35" | The Seal Jaw Service Kit includes: The element pad assembly, pressure pad assembly, 3/8″ heater element, one Stainless Steel finger nut, one brass nut, and a strip of 2 1/2″ PTFE Fabric tape with a 1″ non-adhesive zone for over the element. Not for Dual (Upper & Lower) heat versions. | $184.00 | |
| Stainless Steel Finger Nut | The stainless steel finger nut is used to secure the element to the slider post assembly. | $9.00 |