Model HDMP3-TC
| Name | Summary | Price | Buy |
|---|---|---|---|
| 2-1/2″ wide PTFE Fabric Tape with 1″ non-sticky zone down the middle for over the element. – 108′ Roll | 2-1/2″ wide PTFE Fabric Tape with 1″ non-sticky zone down the middle for over the element. – 108′ Roll | $279.85 | |
| 2-1/2″ wide PTFE Fabric Tape with 1″ non-sticky zone down the middle for over the element. – 50′ Roll | 2-1/2″ wide PTFE Fabric Tape with 1″ non-sticky zone down the middle for over the element. – 50′ Roll | $193.85 | |
| Element Pad Assembly for HDMP_TC 30″ (Need 1 for each bar) | Element pad assembly is the pad under the heater element that consists of 1/16″ grey rubber covered with 3/4″ wide PTFE fabric tape. The EPA is centered on top of the red fiberglass material on the seal bar. Generally need 2 pcs for each machine. One for the upper bar heating element and 1 for the lower bar element. | $52.00 | |
| Element Pad Assembly for HDMP_TC 35″ (Need 1 for each bar) | Element pad assembly is the pad under the heater element that consists of 1/16″ grey rubber covered with 3/4″ wide PTFE fabric tape. The EPA is centered on top of the red fiberglass material on the seal bar. Generally need 2 pcs for each machine. One for the upper bar heating element and 1 for the lower bar element. | $55.00 | |
| Element Pad Assembly for HDMP_TC 40″ (Need 1 for each bar) | Element pad assembly is the pad under the heater element that consists of 1/16″ grey rubber covered with 3/4″ wide PTFE fabric tape. The EPA is centered on top of the red fiberglass material on the seal bar. Generally need 2 pcs for each machine. One for the upper bar heating element and 1 for the lower bar element. | $58.00 | |
| Element Pad Assembly for HDMP_TC 50″ (Need 1 for each bar) | Element pad assembly is the pad under the heater element that consists of 1/16″ grey rubber covered with 3/4″ wide PTFE fabric tape. The EPA is centered on top of the red fiberglass material on the seal bar. Generally need 2 pcs for each machine. One for the upper bar heating element and 1 for the lower bar element. | $62.00 | |
| Exhaust Silencer for Vacuum Sealers with 1/2″ Exhaust Port(s) | Exhaust Silencer with 1/2″ tube is used to quiet the exhaust noise from the vacuum sealer. For Models: HDMP, 635HP, Validatable 635 Gas and Vac models, 635G, and 8000. | $110.00 | |
| Foot Switch (Electric, 3 Wire) with 8′ Cord (Not for models 235, 35 nor 35G) | Replacement Foot switch with 8′ wire for all models Except 235, 35 and 35G. See part #306-0069 for switch only (without cable) for ease of installation or if you have an extended cable (longer than 8′). | $108.85 | |
| Foot Switch without cord | Replacement Foot switch without cable. May be easier to install as no entry to case will be needed. Pay close attention to how wires are connected to your current switch so new switch can be wired correctly. | $56.85 | |
| Grommet, Silicone Black | Grommet for Constant Heat Seal Bar and HDMP Vacuum Nozzle Cylinders. | $9.00 | |
| Heating Element – 3/8″ x 20″ for HDMP_-2B_ and 675_-20-_B | Heating Element – 3/8″ x 20″ for HDMP_-2B_ and 675_-20-_B | $85.85 | |
| Heating Element – 3/8″ x 25″ for HDMP_-3B_ and 675_-25-_B | Heating Element – 3/8″ x 25″ for HDMP_-3B_ and 675_-25-_B | $98.85 | |
| Heating Element – 3/8″ x 30″ for HDMP_-4B_ and 675_-30-_B | Heating Element – 3/8″ x 30″ for HDMP_-4B_ and 675_-30-_B | $104.85 | |
| Heating Element – 3/8″ x 35″ for HDMP_-5B_ | Heating Element – 3/8″ x 25″ for HDMP_-5B | $130.00 | |
| Heating Element – 3/8″ x 40″ for HDMP_-6B_ | Heating Element – 3/8″ x 40″ for HDMP_-6B_ | $127.00 | |
| Heating Element – 3/8″ x 50″ for HDMP_-7B_ | Heating Element – 3/8″ x 40″ for HDMP_-6B_ | $130.00 | |
| Heating Element – 3/8″ x 60″ for HDMP_-8B_ | Heating Element – 3/8″ x 40″ for HDMP_-6B_ | $143.00 | |
| Replacement filter cartridge for Optional Vacuum Filter | The replacement filter is used in the vacuum filter # 104-0009 and 104-0013. | $20.00 | |
| Thermocouple Assembly with boot, tube & 15″ long yellow sleeve | Thermocouple is used to sense heat at the seal area on the impulse heat sealer. This model of replacement thermocouple is held in place by a small piece of blue tubing and taped in place for easy installation on your validatable heat sealer. This NEMA thermocouple has a silicone boot. | $289.85 | |
| Vacuum Filter- 3/8″ In/Out. Only for machines with existing filters | The vacuum Filter is used to remove moisture or liquids from the vacuum lines on HDMP Vacuum Sealers. In/Out (3/8″). Filters particles to 10 microns. Vacuum Filter uses replacement filter cartridge# 104-0012. This is only for machines with existing filters. | $129.00 | |
| Vacuum Pad 1/2″x3/8″ Black Rubber with adhesive. 10′ – 4″ Roll for HDMP_ GV Machines | Vacuum Pad 1/2″x3/8″ Black Rubber with adhesive. 10′ – 4″ Roll for HDMP_ GV Machines | $74.00 |